| 3R6-63E9 Rotek Slewing Ring Bearings | J max.:434.975 mm; Mass pillow block:90.3 kg; Cap bolt, SAE grade:8; Stabilizing ring:SR-28-0; End plug (suffix Y):EPR 27; Initial grease fill:850.5 g; J min.:406.4 mm; h:52.388 mm; Cap bolt recommended tightening torque:515.2 N·m; H2:60.325 mm; da:122.237 mm; N1:28.575 mm; Housing:SAW 528; Pa:37 kN; Appropriate attachment bolt size G:1 in; Ca:92.939 mm; R2:30.163 mm; Taconite seal:2 x TER 120; |
| 232.20.0400.503 Type 21/520.2 Standard 5 Slewing Ring Bearings | da min.:484 mm; Mass bearing (including seat washer where applicable):6.4 kg; d:460 mm; D:500 mm; Da max.:476 mm; Minimum load factor A:4.7; Limiting speed:1500 r/min; H:30 mm; Basic static load rating C0:950 kN; ra max.:1 mm; Reference speed:1100 r/min; r1,2 min.:1 mm; d1 ≈:498.5 mm; Basic dynamic load rating C:130 kN; D1 ≈:461.5 mm; Fatigue load limit Pu:17.6 kN; |
| S10-63E1 Rotek Slewing Ring Bearings | rs (min):3 mm; E:170 mm; Static (Coa):293 kN; b1:22 mm; D:200 mm; B:48 mm; b:13 mm; F:110 mm; r1s (min):3 mm; Dynamic (Ca):299 kN; s:2 mm; Pu:32.300 kN; d2 (max):123.8 mm; d2:80 mm; |
| R8-52N3 Rotek Slewing Ring Bearings | End plug (suffix Y):EPR 8; Ca:42.799 mm; Initial grease fill:87.885 g; ba:33.337 mm; Cap bolt, SAE grade:8; P90°:82.7 kN; Cap bolt:2 x 5/8-11 UNC; R2:21.431 mm; Taconite seal:TER 44; Da:140 mm; Max. speed for Taconite seal:1150 r/min; Stabilizing ring:SR-16-13; P120°:49.8 kN; RG:3/8 NPT; R1:53.181 mm; Housing:SSAFS 516; A1:88.9 mm; S:4.763 mm; P60°:138 kN; h:31.75 mm; |
| 61.20.0644.500.01.1503 Standard 5 Slewing Ring Bearings | l1 min.:115 mm; r1 min.:1 mm; l2 max.:281 mm; Basic dynamic load rating C:365 kN; dk:80 mm; d:60 mm; α:6 °; h:210 mm; Specific dynamic load factor K:150 N/mm²; Mass rod end:5.7 kg; G:M 52x3; l7 min.:73 mm; C1 max.:39 mm; B:44 mm; d2 max.:137 mm; Basic static load rating C0:360 kN; Material constant KM:330; |
| 232.20.0800.013 Type 21/950.2 Standard 5 Slewing Ring Bearings | B1:59 mm; Fatigue load limit Pu:28.5 kN; Basic static load rating C0:250 kN; D1 ≈:125 mm; D:140 mm; Operating clearance factor k2:0.121; Limiting speed:6000 r/min; d1:70 mm; d3:105 mm; Ba min.:12 mm; Da min.:116 mm; r1,2 min.:2 mm; s1 max.:9.1 mm; Basic dynamic load rating C:220 kN; B:33 mm; Mass bearing + sleeve:2.9 kg; ra max.:2 mm; d2 ≈:98.1 mm; db min.:85 mm; da max.:107 mm; |
| 60.35.0680.000.11.1503 Standard 5 Slewing Ring Bearings | r1s (min):1.1 mm; Pu:7.400 kN; Dynamic (Ca):61.9 kN; s:1.4 mm; E:76.5 mm; Static (Coa):60.7 kN; D:85 mm; d2:45 mm; B:19 mm; b:5 mm; b1:8.5 mm; d2 (max):59.1 mm; F:55 mm; rs (min):1.1 mm; |
| 3R8-98E9 Rotek Slewing Ring Bearings | H1:420 mm; A1:430 mm; Eye bolt, size:2 x M 42; N4 max.:35 mm; Locating ring:2 x FRB 29.5/720; P180°:4000 kN; J:1030 mm; A2:455 mm; Oil level, min.:94 mm; Appropriate attachment bolt, rec. tightening torque:3640 N·m; da:470 mm; Ca:226 mm; Q180°:2900 kN; Cap bolt, rec. tightening torque:850 N·m; Cap bolt, size:M 42x280; Da:720 mm; H:835 mm; Mass housing:751 kg; Appropriate attachment bolt, size G:42 mm; |
| R8-49E3 Rotek Slewing Ring Bearings | h:110 mm; d:30 mm; Basic static load rating C0:104 kN; l1 min.:65 mm; Basic dynamic load rating C:176 kN; G:M 30x2; B:22 mm; Specific dynamic load factor K:300 N/mm²; l2 max.:149 mm; dk:40.7 mm; C1 max.:20 mm; α:6 °; Mass rod end:0.9 kg; l7 min.:34 mm; r1 min.:0.6 mm; d2 max.:75 mm; |
| 61.20.0630.100.11.1503 Standard 5 Slewing Ring Bearings | H1:125.425 mm; L:419.1 mm; S:4.763 mm; Da:200 mm; Initial grease fill:232.47 g; Max. speed for PosiTrac Plus seal:1450 r/min; A1:120.65 mm; A2:165.1 mm; PG:1/4 NPT; Stabilizing ring:SR-22-19; J max.:368.3 mm; P60°:178 kN; Cap bolt:5/8-11 UNC; Labyrinth ring:2 x LOR 109; End plug (suffix Y):EPR 13; Mass pillow block:52.2 kg; Cap bolt recommended tightening torque:298.3 N·m; ba:50.006 mm; |
| 162.20.0450.890.11.1503 Standard 5 Slewing Ring Bearings | da min.:53.2 mm; Static axial stiffness, preload class B:63 N/µm; Fatigue load limit Pu:0.44 kN; db min.:53.2 mm; a:14.2 mm; Basic static load rating C0:10.4 kN; d:50 mm; db max.:56.6 mm; Preload class C GC:200 N; Calculation factor fHC:1.04; Preload class A GA:50 N; Basic dynamic load rating C:13.5 kN; Calculation factor f2A:1; r3,4 min.:0.3 mm; Calculation factor f2C:1.12; d2:57.1 mm; Static axial stiffness, preload class D:122 N/µm; |
| 62.20.0630.000.11.1503 Standard 5 Slewing Ring Bearings | End plug (suffix Y):X-5217-2; Max. speed for PosiTrac Plus seal:575 r/min; PG:1/4 NPT; Labyrinth ring:2 x LOR 568; A1:228.6 mm; P150°:222 kN; RG:1 NPT; P60°:669 kN; R2:50.8 mm; L:869.95 mm; Eye bolt:2 x 1/2-13 UNC; Stabilizing ring:2 x A8819; Housing:SSAFS 056 KAUB; Pa:89 kN; H:495.3 mm; H1:250.825 mm; Bearing:23056 CCK/W33; h:73.025 mm; Cap bolt recommended tightening torque:4284.4 N·m; |
| 162.16.0560.891.21.1503 Standard 5 Slewing Ring Bearings | Static axial stiffness, preload class B:32 N/µm; Calculation factor f1:1; ra max.:0.6 mm; db max.:24.4 mm; Attainable speed for grease lubrication:54000 r/min; d1:26.6 mm; r1,2 min.:0.6 mm; a:10.2 mm; d2:24.8 mm; rb max.:0.3 mm; Calculation factor fHC:1; d:20 mm; Preload class A GA:40 N; Basic static load rating C0:3.35 kN; Calculation factor f:1.04; Preload class C GC:235 N; Static axial stiffness, preload class C:44 N/µm; |
| 62.20.0450.001.21.1503 Standard 5 Slewing Ring Bearings | d2 ≈:169 mm; da min.:158 mm; b:8.3 mm; G:M 160x3; D1 ≈:211 mm; Calculation factor Y0:1.8; Basic dynamic load rating C:1054 kN; Calculation factor Y2:2.7; Limiting speed:2000 r/min; Mass bearing + sleeve:21 kg; Calculation factor e:0.37; B:100 mm; Fatigue load limit Pu:146 kN; ra max.:2 mm; r1,2 min.:2.1 mm; B2 ≈:126 mm; K:4.5 mm; d1:145 mm; Reference speed:1400 r/min; Da max.:238 mm; |
| R11-79N3 Rotek Slewing Ring Bearings | A1:180.975 mm; Mass pillow block:144 kg; Initial grease fill:1304.1 g; P60°:234 kN; Cap bolt:4 x 3/4-10 UNC; P150°:75.6 kN; H1:190.5 mm; Labyrinth ring:2 x LOR 148; R2:41.275 mm; PG:1/4 NPT; L:679.45 mm; J max.:600.075 mm; End plug (suffix Y):EPR 19; ba:88.106 mm; A2:250.825 mm; Housing:SAW 536; Cap bolt, SAE grade:5; P180°:89 kN; h:60.325 mm; Pa:60.5 kN; |
| 161.20.0560.890.11.1503 Standard 5 Slewing Ring Bearings | Cap bolt recommended tightening torque:271.2 N·m; Mass pillow block:153 kg; J max.:619.125 mm; J1:114.3 mm; Da:339.999 mm; P150°:94.3 kN; Initial grease fill:1672.65 g; Taconite seal:TER 167; Appropriate attachment bolt size G:1.25 in; J min.:549.275 mm; H1:200.025 mm; P60°:290 kN; A1:190.5 mm; Cap bolt, SAE grade:5; Cap bolt:4 x 7/8-9 UNC; h:57.15 mm; L:711.2 mm; PG:1/4 NPT; P120°:107 kN; |
| No. | Brand | S | T | N | w | K | f | h | E |
| 232.20.0800.503 Type 21/950.2 | Standard 5 | - | - | - | - | - | - | - | - |
| 60.20.0744.575.01.1403 | Standard 5 | - | - | 60 mm | - | - | - | - | - |
| 62.20.0710.000.11.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 162.25.0764.890.11.1503 | Standard 5 | - | 48.5 mm | - | - | - | - | - | - |
| 231.21.0775.013 Type 21/850.1 | Standard 5 | - | - | - | - | - | - | - | - |
| 162.20.0450.891.21.1503 | Standard 5 | 0.794 mm | - | - | - | - | - | - | - |
| H8-54N1 | Rotek | 0.794 mm | - | - | - | - | - | - | - |
| 62.20.0544.500.01.1503 | Standard 5 | - | - | - | - | 12 mm | - | - | - |
| 162.20.0630.890.11.1503 | Standard 5 | 3.175 mm | - | - | - | - | - | 28.575 mm | - |
| 250.15.0375.013 Type 13/4 | Standard 5 | 0.794 mm | - | - | - | - | - | - | - |
| R8-46E3 | Rotek | - | - | - | - | - | - | - | - |
| A24-119E11A | Rotek | - | - | - | - | - | - | - | - |
| A16-95N6 | Rotek | - | - | - | - | - | - | - | - |
| 3R16-102P5 | Rotek | - | - | - | 50 mm | - | - | - | - |
| 162.16.0630.890.11.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 61.20.0744.500.01.1503 | Standard 5 | 0.794 mm | - | - | - | - | - | - | - |
| 3R6-49N9 | Rotek | 4.763 mm | - | - | - | - | - | - | - |
| 232.21.0475.013 Type 21/520.2 | Standard 5 | - | - | - | - | - | - | - | - |
| A18-74E3 | Rotek | - | - | - | - | - | - | - | - |
| 3R10-111N2F | Rotek | - | - | - | - | - | - | - | - |
| 62.20.0630.001.21.1503 | Standard 5 | - | - | - | - | - | - | - | 1044 mm |
| 60.22.0575.502.11.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 62.20.0414.500.01.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 230.20.0800.503 Type 21/950. | Standard 5 | 4.763 mm | - | - | - | - | - | 34.925 mm | - |
| 61.20.0744.575.01.1403 | Standard 5 | - | - | - | - | - | - | - | - |
| S20-125E1 | Rotek | 2.5 mm | - | - | - | - | - | - | - |
| 61.25.0764.103.11.1504 | Standard 5 | - | - | - | - | - | - | - | - |
| 60.20.0544.575.01.1403 | Standard 5 | - | - | - | - | 9 mm | - | - | - |
3R13-62N1E Rotek Slewing Ring Bearings Video
3R13-62N1E Internal Gear Heavy Duty Slewing Ring(70.5
3R13-62N1E Internal Gear Heavy Duty Slewing Ring(70.5*50.2*8.62inch) For Climbing Cranes And Tower Cranes 50.2x70.5x8.62- 3R13-62N1E bearing,Seals
3R13-62N1E slewing ring bearings with internal gear - JCB
Page 1. Luoyang JCB Bearing Technology Co., Ltd
3R13-62N1E - Rotek Slewing Rings Online Catalog | Lily
Find details about 3R13-62N1E slewing rings, Choose from our selection of rotek bearings, including over 800 products in a wide range of styles and sizes
3R13-62N1E Internal Gear Heavy Duty Slewing Ring(70.5
3R13-62N1E Internal Gear Heavy Duty Slewing Ring(70.5*50.2*8.62inch) For Climbing Cranes And Tower Cranes 50.2x70.5x8.62- 3R13-62N1E bearing,Seals
Large-Diameter Anti-Friction Slewing Rings - Rotek Inc
3R13-62N1E. 8.62. 8.12. 1.87. 6.75. 70.50. 59.80. 60.31. 50.200. 51.000. 2.0. STUB. 250-300. 3R13-122N1B. 9.00. 8.50. 1.00 ... 3R13-128N1A. 12.32. 8.27
3R13-62N1E - Rotek Slewing Rings Online Catalog | Lily
Find details about 3R13-62N1E slewing rings, Choose from our selection of rotek bearings, including over 800 products in a wide range of styles and sizes
3R13-62N1E slewing ring bearings with internal gear - JCB
Page 1. Luoyang JCB Bearing Technology Co., Ltd