| A16-78E4 Rotek Slewing Ring Bearings | Taconite seal:TER 36; N1:22.225 mm; L:349.25 mm; H1:101.6 mm; PG:1/8 NPT; R2:27.94 mm; RG:3/8 NPT; Pa:8.27 kN; P150°:40.5 kN; Mass pillow block:21.5 kg; Appropriate attachment bolt size G:0.75 in; A2:223.838 mm; da:60.325 mm; P180°:49.8 kN; Max. speed for Taconite seal:1250 r/min; Ca:64.795 mm; Cap bolt, SAE grade:8; h:42.862 mm; P60°:121 kN; Initial grease fill:286.33 g; |
| L9-53P9Z Rotek Slewing Ring Bearings | Da max.:101 mm; B:28 mm; B1:47 mm; D:110 mm; d3:80 mm; b:6 mm; Mass bearing + sleeve:1.45 kg; Calculation factor Y0:2.8; Basic dynamic load rating C:159 kN; d1:55 mm; Fatigue load limit Pu:18.6 kN; Calculation factor Y1:2.8; d2 ≈:72.7 mm; Reference speed:5600 r/min; D1 ≈:96.5 mm; da max.:72 mm; ra max.:1.5 mm; Calculation factor Y2:4.2; Limiting speed:7500 r/min; B4:13 mm; |
| 162.25.0886.891.21.1503 Standard 5 Slewing Ring Bearings | Housing material:Cast iron; Recommended diameter for attachment bolts, inch G:0.375 in; L:86 mm; J6:74 mm; Db2:63 mm; RG:1/4-28 UNF; Db1:57 mm; Mass bearing unit:0.53 kg; Hexagonal key size for grub screw N:3 mm; Limiting speed:1800 r/min; Thread grub screw G2:M6x0.75; Basic static load rating C0:6.55 kN; J:63.5 mm; Recommended diameter for attachment bolts, mm G:10 mm; Recommended tightening torque for grub screw:4 N·m; |
| 162.16.0630.891.21.1503 Standard 5 Slewing Ring Bearings | da max.:210 mm; ra max.:2 mm; Da max.:249 mm; Misalignment factor k1:0.105; D:260 mm; Limiting speed:2800 r/min; Mass bearing:12.4 kg; Reference speed:2200 r/min; Operating clearance factor k2:0.117; Basic dynamic load rating C:750 kN; s1 max.:19 mm; D1 ≈:236 mm; d2 ≈:195 mm; Basic static load rating C0:1080 kN; B:67 mm; d:170 mm; da min.:181 mm; Ca min.:1.2 mm; Da min.:226 mm; Fatigue load limit Pu:100 kN; |
| H8-54N1 Rotek Slewing Ring Bearings | H1:95.25 mm; Mass bearing unit:16.6 kg; B:80.169 mm; H:190.5 mm; da:87.313 mm; Limiting speed:2300 r/min; Basic dynamic load rating C:325 kN; Attachment bolt diameter G:19.05 mm; A:114.3 mm; s:40.084 mm; J max.:298.45 mm; L:355.6 mm; H2:57.15 mm; S:0.794 mm; J1:60.325 mm; J min.:266.7 mm; |
| 231.20.0700.503 Type 21/850.1 Standard 5 Slewing Ring Bearings | Hydraulic nut:HMV 56 E; A:9 mm; Mass withdrawal sleeve:19 kg; G2:G 1/4; d1:240 mm; G1:30 mm; B2:213 mm; G:Tr 280x4; B1:205 mm; d:260 mm; |
| 3R8-59N2E Rotek Slewing Ring Bearings | P0°:6000 kN; Taconite seal:2 x TK 76; P90°:3600 kN; bb:117 mm; A1:360 mm; bc:202.5 mm; Appropriate attachment bolt, rec. tightening torque:2280 N·m; L:950 mm; Locating ring:2 x FRB 20/580; A:400 mm; Eye bolt, size:2 x M 30; Bearing (basic designation):22264; Labyrinth seal:2 x TS 76/340; P180°:3000 kN; N:50 mm; P150°:2300 kN; End cover:ETS 76; J6:880 mm; db:340 mm; J1:220 mm; |
| 61.20.0450.100.11.1503 Standard 5 Slewing Ring Bearings | Permissible sliding velocity v max.:0.5 m/s; a:3 mm; Tolerance shaft:e7; Specific static load factor K0:45 N/mm²; D:20 mm; Coefficient of friction µ max.:0.15; Permissible sliding velocity v min.:0 m/s; h:15 mm; d:14 mm; Specific dynamic load factor K:25 N/mm²; Coefficient of friction µ min.:0.08; B:30 mm; Mass bushing:0.042 kg; Tolerance housing:H7; α:105 °; |
| 61.20.0644.575.01.1403 Standard 5 Slewing Ring Bearings | Mass adapter sleeve assembly:3.6 kg; G:M 120x2; d:120 mm; B:20 mm; B4:22 mm; B1:112 mm; d3:155 mm; Hydraulic nut:HMV 24 E; d1:106.362 mm; |
| 250.14.0400.013 Type 13/5 Standard 5 Slewing Ring Bearings | D2 ≈:8.2 mm; Basic static load rating C0:0.114 kN; Limiting speed:63000 r/min; d:3.175 mm; Fatigue load limit Pu:0.005 kN; Basic dynamic load rating C:0.364 kN; da min.:4 mm; Calculation factor f0:6.5; Mass bearing:0.0012 kg; Calculation factor kr:0.025; Da max.:8.3 mm; D:9.525 mm; ra max.:0.3 mm; Reference speed:130000 r/min; da max.:4.5 mm; d2 ≈:4.6 mm; B:3.967 mm; r1,2 min.:0.3 mm; |
| 3R10-88N2B Rotek Slewing Ring Bearings | Basic dynamic load rating C:12.7 kN; T:37.3 mm; d:19.05 mm; B:31 mm; Hexagonal key size for grub screw N:3.175 mm; Fatigue load limit Pu:0.28 kN; Bearing:YAR 204-012-2RF/VE49; Recommended diameter for attachment bolts, mm G:10 mm; Db:59 mm; N:12.3 mm; J:63.5 mm; Limiting speed:5000 r/min; L:86 mm; Thread grub screw G2:1/4-28 UNF; Recommended diameter for attachment bolts, inch G:0.375 in; Housing material:Composite for food a; |
| 3R6-55E9 Rotek Slewing Ring Bearings | E:26 mm; Limiting speed:22000 r/min; Fatigue load limit Pu:1.96 kN; da:25.6 mm; Db:20.4 mm; Reference speed:19000 r/min; ra max.:0.3 mm; Basic static load rating C0:16.3 kN; B:12 mm; r1,2 min.:0.3 mm; Basic dynamic load rating C:12.8 kN; Da:26.5 mm; F:20 mm; Mass bearing:0.047 kg; s max.:0.5 mm; D:32 mm; db:19.7 mm; d:15 mm; |
| 62.20.0644.575.01.1403 Standard 5 Slewing Ring Bearings | l:20.55 mm; Db min.:461 mm; Basic dynamic load rating C:2852 kN; d:320 mm; Calculation factor Y0:1.4; Fatigue load limit Pu:500 kN; Reference speed:700 r/min; C:168 mm; Calculation factor e:0.46; T:220 mm; d1 ≈:399.5 mm; D:480 mm; a:226 mm; Cb min.:26 mm; b:10 mm; Calculation factor Y2:2.2; Mass bearing pair:128 kg; Limiting speed:1100 r/min; db min.:342 mm; r5 min.:1.5 mm; |
| W14-71P1 Rotek Slewing Ring Bearings | r max.:2.5 mm; Permissible sliding velocity v max.:1 m/s; Coefficient of friction µ min.:0.08; Tolerance housing:H7 m/s; Tolerance shaft:f7 m/s; B:50 mm; d:100 mm; D1:120 mm; B1:2.5 mm; Coefficient of friction µ max.:0.15; Permissible sliding velocity v min.:0 m/s; Specific static load factor K0:120 N/mm²; Specific dynamic load factor K:40 N/mm²; D:105 mm; Mass bushing:0.39 kg; |
| 62.20.0630.000.11.1503 Standard 5 Slewing Ring Bearings | End plug (suffix Y):X-5217-2; Max. speed for PosiTrac Plus seal:575 r/min; PG:1/4 NPT; Labyrinth ring:2 x LOR 568; A1:228.6 mm; P150°:222 kN; RG:1 NPT; P60°:669 kN; R2:50.8 mm; L:869.95 mm; Eye bolt:2 x 1/2-13 UNC; Stabilizing ring:2 x A8819; Housing:SSAFS 056 KAUB; Pa:89 kN; H:495.3 mm; H1:250.825 mm; Bearing:23056 CCK/W33; h:73.025 mm; Cap bolt recommended tightening torque:4284.4 N·m; |
| 231.20.0600.013 Type 21/750.1 Standard 5 Slewing Ring Bearings | G:Tr 900x7; B2 ≈:445 mm; b:22.3 mm; Limiting speed:360 r/min; Da max.:1192 mm; d1:800 mm; Fatigue load limit Pu:1900 kN; Calculation factor Y2:3.7; K:12 mm; D1 ≈:1088 mm; da min.:866 mm; Calculation factor e:0.27; D:1220 mm; d2 ≈:957 mm; Basic static load rating C0:31500 kN; Calculation factor Y0:2.5; Basic dynamic load rating C:15183 kN; B:365 mm; ra max.:6 mm; B1:415 mm; |
| No. | Brand | S | T | N | w | K | f | h | E |
| A16-152E2 | Rotek | - | - | - | - | - | - | - | - |
| 62.20.0560.001.21.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 250.14.0300.013 Type 13/4 | Standard 5 | - | - | - | - | - | - | - | - |
| 162.16.0450.890.11.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| R9-55N3 | Rotek | - | - | - | - | - | - | 38.1 mm | - |
| 61.20.0450.101.21.1503 | Standard 5 | - | - | - | - | 5 mm | - | - | - |
| 61.20.0544.575.01.1403 | Standard 5 | 4.763 mm | - | - | - | - | - | - | - |
| 3R6-55N9 | Rotek | - | - | - | - | - | - | - | - |
| 161.20.0560.890.11.1503 | Standard 5 | - | - | - | - | - | - | 57.15 mm | - |
| 60.20.0744.575.01.1403 | Standard 5 | - | - | 60 mm | - | - | - | - | - |
| A10-47E1 | Rotek | - | - | - | - | - | - | - | - |
| S16-112E1 | Rotek | - | - | - | - | - | - | - | - |
| 62.20.0560.000.11.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| A19-150P1 | Rotek | 0.794 mm | - | - | - | - | - | - | - |
| A18-89P1 | Rotek | - | - | - | - | - | - | - | - |
| 11.20.0755.000.11.1504 | Standard 5 | - | - | - | - | - | - | - | - |
| R11-75E3 | Rotek | - | - | 10.7 mm | - | - | - | - | - |
| R8-49N3 | Rotek | - | - | - | - | - | - | - | - |
| 162.16.0630.890.11.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| A12-47N3E | Rotek | - | - | - | - | - | - | - | - |
| 230.21.0475.013 Type 21/520. | Standard 5 | - | - | - | - | - | - | - | - |
| L9-49E9Z | Rotek | 0.794 mm | - | - | - | - | - | - | - |
| 61.20.0644.500.01.1503 | Standard 5 | - | - | - | - | - | - | 210 mm | - |
| 3R6-55E9 | Rotek | - | - | - | - | - | - | - | 26 mm |
| 161.20.0450.891.21.1503 | Standard 5 | - | - | - | 80 mm | - | - | - | - |
| W13-49P1 | Rotek | - | - | - | - | - | - | 225 mm | - |
| 3R13-62N1E | Rotek | - | 182 mm | - | - | 10 mm | - | - | - |
| 162.25.0886.891.21.1503 | Standard 5 | - | 37.3 mm | - | - | - | - | - | - |
| 250.15.0300.013 Type 13/4 | Standard 5 | - | - | - | - | - | - | 73.025 mm | - |
| 231.20.0600.503 Type 21/750.1 | Standard 5 | - | - | - | - | - | - | 40.481 mm | - |
L9-57N9Z Rotek Slewing Ring Bearings Video
China Internal Gears Slewing Rings Bearings Rotek Ball
China Internal Gears Slewing Rings Bearings Rotek Ball Bearings Turntable Bearings L9-57n9z for Pump Truck Cranes, Find details about China Slewing
L9-57N9Z slewing ring bearings with internal gear - JCB Bearing
Page 1. Luoyang JCB Bearing Technology Co., Ltd
China Internal Gears Slewing Rings Bearings Rotek Ball
Internal Gears Slewing Rings Bearings Rotek Ball Bearings Turntable Bearings L9-57n9z for Pump Truck Cranes picture from Luoyang Huayang Special
Rotek series slewing ring Luoyang JCB Bearing Technology
47.24. 36.16. 3.54. L9-42N9Z. 51.18. 39.76. 3.54. L9-46N9Z. 55.12. 43.76. 3.54. L9-49N9Z. 59.06. 47.76. 3.54. L9-53N9Z. 62.99. 51.76. 3.54. L9-57N9Z
L9-57N9Z - Rotek Slewing Rings Online Catalog | Lily Bearing
Find details about L9-57N9Z slewing rings, Choose from our selection of rotek bearings, including over 800 products in a wide range of styles and sizes
China Internal Gears Slewing Rings Bearings Rotek Ball
China Internal Gears Slewing Rings Bearings Rotek Ball Bearings Turntable Bearings L9-57n9z for Pump Truck Cranes, Find details about China Slewing
Rotek series slewing ring Luoyang JCB Bearing Technology
47.24. 36.16. 3.54. L9-42N9Z. 51.18. 39.76. 3.54. L9-46N9Z. 55.12. 43.76. 3.54. L9-49N9Z. 59.06. 47.76. 3.54. L9-53N9Z. 62.99. 51.76. 3.54. L9-57N9Z